Things You'll Need
- Dresser (or entertainment center, coffee table, etc.)
- Safety glasses
- Drill and large drill bits
- Jigsaw (if main dresser compartment is divided)
- Sandpaper
- Water-based polyurethane paint
- Paintbrush
- Well-ventilated work area
- Clear Plexiglas (enough to cover the front of the dresser)
- Razor knife or box cutter
- Small hinges
- Metal slide latches
- Wood screws
- Screwdriver
- Silicone aquarium sealant
- Plastic storage container or dishpan (sized to fit the pet and the dresser)
- Sterile potting soil
- Sphagnum peat moss
- Sterile branches (diameter at least as large as pet's body)
- Potted plants (e.g., dracaena or philodendron)
- Fluorescent full-spectrum light fixture (with bulbs)
- Ceramic heat-emitter lamp
- Ceramic lamp-holder bracket
Instructions
Plan Your Vivarium
Make a sketch of the dresser you plan to convert to a vivarium.
Decide where to place a hinged Plexiglas access door; you will need to be able to attach small hinges and latches to the frame or drawer supports.
Select optimal locations for the water dish, full-spectrum light and heat lamp. Make sure that the water dish is easily accessible for cleaning and the heat lamp is placed a safe distance from a basking shelf or perch.
Prepare the Dresser
Remove drawers from the dresser and set aside. Remove any knobs or hinges that you plan to reuse in your vivarium.
Use a jigsaw to cut large access holes in any vertical partitions in the dresser. Drill a pilot hole to insert the saw blade. Cut the holes large enough for branches to pass through, so that your pet reptile(s) can climb easily between sections. Wear safety glasses when drilling or cutting.
Remove any unnecessary horizontal drawer supports from the dresser. Leave supports on the face of the dresser if you will need them to attach the Plexiglas access door.
Drill holes in the back of the dresser for the full-spectrum and heat-lamp plugs.
Sandpaper any rough edges to prevent splintering.
Assemble the Vivarium
Apply three to five coats of water-based polyurethane paint to the inside of the dresser only; coat all surfaces. Work in a well-ventilated area and allow paint to dry completely between coats.
Measure and mark the Plexiglas pieces that will cover the front of your vivarium and form the access door. Score the Plexiglas along the cut lines by pressing firmly with a razor knife. Place a pencil under the scored line and press firmly on each side to break the Plexiglas along the score line. Mark and drill screw holes in the Plexiglas. Remove the thin plastic-wrap coating from each side of the Plexiglas.
Attach the hinges and latches to the Plexiglas access door using silicone aquarium sealant. Allow to dry completely. Attach the Plexiglas to the dresser using wood screws and hinges. Mark and drill holes for the access-door latch pins.
Seal the Plexiglas front to the dresser edge using a thin line of silicone aquarium sealant around the inner edge. Allow to dry completely.
Attach the fluorescent light fixture and ceramic heat-lamp holder to the inside of the assembled vivarium. Pass the power cords through the predrilled holes in the back of the vivarium. Use silicone aquarium sealant to fill the gap around each power cord. Allow to dry completely.
Decorate the Vivarium
Add the water dish to the completed vivarium.
Fill the bottom of the vivarium with a mixture of moist potting soil and sphagnum peat moss. The soil should be level with the top of the water dish.
Add branches to the vivarium in strategic locations to allow your pet reptile(s) to move about the vivarium. Use wood screws to secure the branches in place if needed.
Remove potted plants from their pots and plant them in the vivarium. Leave plenty of room for your pet reptile(s) to move about freely.
Fill the water dish with aged water--tap water that has been allowed to sit overnight so that the chlorine can evaporate.